当前位置: 首页 > 教师队伍 > 走教教师 > 正文

张惠敏

【来源:张惠敏 | 发布日期:2017-04-11 】

张惠敏,教授,为青岛科技大学高密校区学生讲授《塑料成型模具》,《机械制图》课程。

Ø研究领域

高分子材料加工机械

Ø教育经历

1974-1977青岛科技大学 学士

Ø主要论著或科研项目

(1)张惠敏,橡胶工业手册下册,第九分册下册编辑,P89 1994 ISBN7-5025-1375-2

(2)一步法注射成型机.合成橡胶工业,Vol.26 No6 P235 2003 ISSN1000-1255 EI收录期刊

(3)张惠敏.塑料旋转成型的特点与研究.工程塑料应用,Vol.30 No.4P23 2002 ISSN1001-3539 CA已收录

(4)张惠敏.聚氨酯浇注轮胎成型系统的设计和研制.工程塑料应用,Vol.31 No.6 P46 2003

(5)张惠敏.反应注射成型机楔型计量系统的研制.工程塑料应用,Vol.30 No.9 P4 2002

(6)张惠敏.工艺条件和气道结构对气辅成型产品力学性能的影响.工程塑料应用,Vol.31 No.6 P70 2003

(7)张惠敏.应用数值模拟技术优化注塑保压压力,模具技术,2011,(4),45-49

(8)Zhanghuimin .CAE Optimization ofHotRunnerSequentialInjectionMolding for Car interior trim panels,Advanced Polymer Science and Engineering EI收录,2011,V221,461-466

(9)Zhanghuimin .Optimization of Packing Pressure CurveinInjectionMoldingBased on Numerical Simulation,Advanced Polymer Science and Engineering EI收录,2011,V221,522-527

(10)Zhanghuimin .Simulation analysis of residual stress of the plastic gear based on Moldflow,Key Engineering Materials,2012,501,339--343,EI收录

(11)Zhanghuimin .Numerical Simulation and Balance Design of Rubber Injection Mold Gating System Based on POLYFLOW,Key Engineering Materials,2012,501,190-195,EI收录

(12)Zhanghuimin .Optimization of the injection molding process parameters based on moldflow and orthogonal experiment,key Engineering Materials,2013,561,239-243,EI收录

(13)Zhanghuimin .Application of numerical simulation in optimizing rubber injection molding process,key Engineering Materials,2013,561,390-394,EI收录

(14)Zhanghuimin .Application of Numerical Simulation in Optimizing Rubber Injection Molding Process ZhangHuimin Niu Jiateng Dong LeileiKey Engineering Materials Vol. 561 (2013) pp 390-394

(15)Zhanghuimin .The Injection Molding Process Parameters Optimization Based on Moldflow Software and Orthogonal ExperimentYong Nie Huimin Zhang, Jiateng NiuKey Engineering Materials Vol. 561 (2013) pp 239-243

(16)张惠敏.五轴联动数控机床的研制.机床与液压,2010,38(8)

(17)张惠敏.数值模拟方法在橡胶注塑成型中的应用研究.橡胶工业,2015 , 62(7) 422-427

(18)真空橡胶注射成型机的研制,市科技局,005

(19)旋转注射反应注射成型机的研制,国家计委,1999

(20)聚氨酯浇注轮胎的研制,国家计委,1997

(21)新概念轮胎定型硫化机,横向项目,2004

Ø获奖情况

(1)优秀硕士生论文指导,橡胶冷流道注射模具设计及数值模拟应用,教学成果二等奖 2012。

(2)论文:“塑料成型模具”课教学方法的研究与改革,教育教学导刊No.3P26 2005ISSN1813-9884,获优秀论文二等奖。

(3)论文:“如何讲好近机类机制工艺概论课”,中国教育理论杂志vol.31No.8 P67 2003 ISSN1683-376,获优秀论文二等奖.